1、Upper ejector rod was added in the die structure for ease of workpiece separation.
在模具結構中增加了上項桿(上打料棒)，便于工件脫離。

2、The ejector with a lobed nozzle is of high efficiency in pumping and mixing.
波瓣噴管引射器具有高效的引射摻混特性。

3、ANALYTICAL AND EXPERIMENTAL INVESTIGATION OF SUPERSONIC EJECTOR NOZZLE
超音速引射噴管的分析和實驗研究

4、Hide the ejector seat levers.
隱藏彈射座椅的操縱桿。

5、Suitable sizes of push-back pins may be selected from a standard ejector pin range.
回程桿的合適尺寸可以在標準的頂桿范圍內選擇。

6、The plain diameter ejector pin may be used in one of two ways.
普通的頂桿可以有兩種使用方法。

7、The undercut area may stick slide. We may consider to add an ejector pin on the slide.
產品扣位處可能粘行位。我們需考慮行位上加頂針；

8、Part of an engine nacelle and an exhaust ejector are visible at left.
在左側可看見部分的發動機短艙和排氣頂針。

9、The mould plate and ejector grid system is shown in chain-dotted lines in the cross-sectional view.
模板和頂料格架系統在剖面圖上以點劃線表示。

10、Can we add ejector sleeves or ejector pins in the boss of this part?
產品的這個位置不能出模，我們打算做行位，在此面上會有分模線，你接受嗎？

11、In the case of air ejector priming device the operation procedure as follow.
在用自吸裝置的情況下，操作程序如下。

12、Q: Because you'll release this section of the roof and engage and fire the passenger ejector seat.
因?yàn)?/a>你會開了車頂和啟動和發射乘客彈射座椅。

13、Ejector seat levers can only be used once, and their consequences are significant and irreversible.
彈射座椅操縱桿只能用一次，它的使用將引起重要的變化，而且這個。

14、Characteristics and Test Study of Water Jet Air Ejector of 200MW Set
200MW機組射水抽氣器性能試驗研究

15、The direction of movement of this ejector pin is, therefore, controlled by this hole.
因此頂桿的運動方向由這個孔來控制。

16、At last, numerical simulation of this ejector was performed.
最后，對引射器進行了數值模擬。

17、Each ejector pin diameter has a number of different lengths associated with it.
每一種頂桿直徑有許多不同長度。

ejector翻譯

n. 驅逐者, 排出器, 放出器【化】 噴射泵; 噴射器【醫】 噴射器, 剔出物, 排除器 詳情