1、Remove the crankshaft oil slinger.
拆去曲軸拋油環。

2、The power mechanism of the engine is actually called the crankshaft and connecting rod mechanism.
發動機的動力機構實際上就是曲柄連桿機構。

3、Camshaft from the crankshaft through the timing belt or gear or chain drive.
凸輪軸由曲軸通過齒形帶或齒輪或鏈條驅動。

4、The lower end of the connecting rod fits the crankshaft journal.
在連桿大頭安裝曲柄軸頸。

5、A "Tent-Dam" Model to Predict Fatigue Reliability of Crankshaft of ICE
用“帳篷—堤壩”模型預測內燃機曲軸的疲勞可靠性

6、Forging Technology Design of Series 350 Crankshaft of Chevroler
雪佛萊350系列曲軸鍛造工藝設計研究

7、The crankshaft has three main bearing journals.
曲軸有三個主要軸承期刊。

8、Remove the crankshaft from the cylinder block.
從汽缸體上卸去曲軸（參看“汽缸體-拆卸”）。

9、Crankshaft is an important part of truck engine parts, and it is also a fast moving parts.
曲軸是一個重要的組成部分卡車發動機部件，而這也是一個快速移動的零件。

10、The second photo shows the crankshaft center bearing holder installed in the block.
第二圖為曲軸中心軸承持有人安裝在該區塊。

11、Remove front crankshaft belt pulley.
拆卸前曲軸皮帶輪。

12、The crankshaft serves to change the reciprocating power into rotary power.
曲軸的作用是把往返力變?yōu)?a href="/zaoju/35539.htm">旋轉動力。

13、The crankshaft therefore must be adequately strong and wear-resistant.
曲軸因此必須要足夠結實與耐磨。

14、In order to start them, the engine crankshaft must be turned over.
為了啟動發動機，曲軸必須先運轉起來。

15、A study of CAD System for Crankshaft Foundry Process
曲軸鑄造工藝計算機輔助設計系統的研究

16、It is interlocked with the crankshaft via the chain drive.
它通過鏈條驅動機構與曲軸互鎖在一起。

17、Position drive plate on the crankshaft's dowel pin and press on to the crankshaft flange.
將傳動盤安放在曲軸的定位銷上，然后壓到曲軸法蘭上。

18、Check the deflection of the crankshaft both before and after repair.
在修理前和修理后都要檢查曲軸的變形情況。

19、As the crankshaft rotates, the crankpin swings in a circle around the shaft.
隨著曲軸的轉動，曲柄銷繞主軸作圓周擺動。

20、The flywheel mounts to the engine's crankshaft and transmits engine torque to the clutch assembly.
飛輪安裝在發動機曲軸上，它將發動機的扭矩傳遞給離合器總成。

21、Install new front crankshaft oil seal.
安裝新的前曲軸油封。

22、The article introduced a grinding method and principle of the journal of crankshaft connecting rod.
本文簡述了一種正在興起的曲軸連桿軸頸的磨削方法和原理。

23、It has developed the parametric residual deforming FEA in crankshaft rolling process.
二次開發了參數化曲軸滾壓加工殘余變形的有限元分析。

24、In that way, the forces acting on the crankshaft are balanced and vibration is reduced.
以這種方式，在曲軸上的力將會達到平衡而且震動也會減少。

25、The nationalization of engine crankshaft blank for Jetta, Bora and Golf car was realized.
實現了捷達、寶來和高爾夫轎車發動機曲軸毛坯的國產化。

26、Research on Motion Model of Constant h_(eq)Non_circular Crankshaft Grinding
曲軸非圓的恒當量磨削厚度磨削運動模型研究

27、The nationalization of engine crankshaft blank for jetta bora and golf car was realized.
實現了捷達、來和高爾夫轎車發動機曲軸毛坯的國產化。

28、Torsional vibration of engine crankshaft is an important dynamic problem.
扭轉振動是發動機一個重要的動力問題。

29、The wings are driven by a crankshaft that is connected to a gearbox.
機翼由連接著齒輪箱的機軸驅動。

30、High efficiency crankshaft FAE system based on VC++ and ANSYS interface
基于VC++和ANSYS接口的高效率曲軸有限元分析系統

crankshaft翻譯