1、There is no need to field solder or to struggle with a crimp pin.
無需焊接或外地奮斗的卷曲針。

2、Solder side is chosen to measure.
4量測以吃錫面為選擇點。

3、solder together by using hard solder with a high melting point
用高熔點的焊料來連接。

4、Becareful not to overheat the solder and damage the diodes.
注意不要使烙鐵過熱而損壞二極管。

5、tinning the ends of the wires makes a better joint when you solder them
當你焊接接口時，用錫焊很管用。

6、And the different section shape of the solder joint is given with the variation of solder volume.
給出了不同的釬料量對應的焊點剖面形態的變化。

7、Will the sample needs of solder part in flux in 5 to 10 seconds.
將樣品需要焊錫的部分浸入助焊劑中5到10秒。

8、An ideal connection that puts any solder to shame.
這種理想的連結方式，讓其它各類接合方式瞠乎其后。

9、Tin-lead solder in the manufacture of professional audio equipment.
用于制造專業音響設備的鉛錫焊料。

10、The Study on MCM′s Solder Joint Shape
MCM焊點形態研究方法探討

11、Time of solder can be set.
焊錫時間可以根據不同要求設定。

12、When joint is filled, a continuous run of solder or brazing alloy will be visible.
在安裝連接部件時，可以看到焊料和釬焊合金繼續流動。

13、A solder paste used for brazing was developed and its technical performance was investigated.
研制了鋁硬釬焊用釬料膏，對其工藝性能進行了研究。

14、Impact of Solder Pearl on SMC
錫珠對SMC電性能的影響

15、Heat up your soldering iron and tin it by allowing it to melt a drop of solder onto its tip.
加熱你的電烙鐵，通過允許其熱量融化的一滴錫滴在它的尖端來錫化它。

16、The shear strength of BGA joint with eutectic solder is higher than that of tin-lead alloy itself.
共晶釬料BGA球焊點的抗剪強度比錫鉛合金釬料自身的抗剪強度大。

17、Printed circuit board, Solder mask, Flood screen printing, Quality Control.
印制板，阻焊膜，絲網印刷，品質控制。

18、Finally the life of CSP solder joint based on Pb-free material 95.
基于三維有限元分析方法預測熱循環條件下焊點的疲勞壽命，對無鉛材料95。

19、The manufacture of solder bump is one of the key technologies for area array packaging.
釬料凸臺和互連焊點的重熔是面陣封裝的關鍵技術之一。

20、they forget to solder the contacts.
他們忘記了焊接切點。

21、Fewer workers are needed to solder circuit boards.
焊接電路板需要較少的工人。

22、This makes for the best solder job.
這是為了使焊接至臻完美。

23、Lead-free solder wire is one kind of environmental-friendly product with good stability.
無鉛錫線是一種環保型，穩定性很好的產品。

24、So it will result in rigidity skin &block and solder balls etc.
產生的后果是：錫膏出現硬皮、硬塊、難熔并產生大量錫球等。

25、The use of nitrogen will depend on the solder paste flux chemistry.
是否使用氮?dú)馊Q于焊錫膏焊劑的化學特性。

26、PCBA conformal coating, dam process, Solder mask coating, DIP Component fixing.
PCBA表面三防涂覆、堤壩工藝、涂防焊膠、DIP元件加固等。

27、Carefully solder 2 new thin, flexible, insulated wires in place.
小心的將兩條細、易彎曲并且絕緣的新導線焊接到位。

28、Therefore, it is necessary to study the reliability of this mixed solder joint.
因此，有必要對這種混合焊點進行可靠性分析。

29、Less residue, shinny and clean solder spot.
殘留物少，焊點光澤，干凈。

30、The Development of Test Instrument for Solder Paste Print Performance
焊膏印刷性能測試儀器的研制

solder翻譯

n. 焊接劑, 接合物vt. 施以焊接, 焊合, 聯結vi. 施以焊接, 焊合, 聯結【化】 釬焊填充金屬【醫】 焊劑; 焊接 詳情