1、Analysis of 10 kV PT socket bushing flashover in Shajiao C Power Plant
沙角發電C廠兩起10kV　PT插座套管絕緣閃絡事故的分析

2、That way, all movement takes place between the bushing and bearing - instead of on the bolt.
這樣，所有運動的發生之間的襯套和軸承-而不是對螺栓。

3、The longer bronze rod bushing provides a maximum load bearing support.
時間越長青銅連桿襯套提供最大承重的支持。

4、The cast iron rod bushing provides maximum load bearing support.
鑄鐵連桿襯套提供最大承重的支持。

5、Tighten leaf spring press until bushing flange bottoms solidly against leaf spring eye.
上緊葉片彈簧加壓機直到襯套凸緣的底部扎實地扺住葉片彈簧的孔眼。

6、A bushing or similar lining for a bearing, made from a copper alloy
銅套或銅襯墊用銅合金制的軸承軸瓦或套筒式襯墊

7、Improvement of Heat Treatment Process for Vertical Bushing of Dri ll Rigs
鉆機立軸套熱處理工藝的改進

8、The bushing ring flange suitable temperature is decided by the designer according to the situation.
襯環法蘭的適用溫度由設計者根據情況決定。

9、The longer cast iron rod bushing provides maximum load bearing support.
鑄鐵的時間越長連桿襯套提供最大承重的支持。

10、A bushing used to secure a pipe joint
套圈，箍用來縛緊管子接頭的套圈

11、Premature wear failure analysis of track pin bushing in swamp bulldozer
濕地推土機履帶銷套的早期磨損失效分析

12、The function of a bushing is to prevent metals from touching one another
襯套的作用是阻止金屬的彼此碰撞。

13、Oil filled bushing should have plugs for test of power factor.
充油套管應帶有用于進行功率因數試驗的接插頭。

14、The designer may lower the pressure on the packing by placing a throat bushing in the pump case.
設計者可在泵殼內放置喉道補心以降低在填料上的壓力(圖)。

15、Place Taper - lock Bushing and Timing Belt Pulley on the transmission shaft.
將錐面緊固套與同步帶輪裝在傳動輪上。

16、A bushing used to secure a pipe joint.
套圈，箍用來縛緊管子接頭的套圈

17、A bushing or similar lining for a bearing, made from a copper alloy.
銅套或銅襯墊用銅合金制的軸承軸瓦或套筒式襯墊

18、Connection of lead and bushing shall be tight and correct, bushing should be in good condition.
引出線與套管的連接應牢靠，接線正確。套管應完好無損。

19、A New type Ball Bushing Bearing
一種新型滾珠襯套軸承

20、Pump drive shaft and bushing wear, the tolerance clearance increases, will affect oil pump.
齒輪泵主動軸與襯套磨損后，其配合間隙增大，必將影響泵油量。

21、File off both bores to the hexagon of the insertion bushing using a needle-point file.
用細銼將兩個孔銼成鑲?cè)胍r套的六邊形。

22、The steel retaining plate has two functions, retaining the bushing and preventing rod rotation.
固定板的鋼具有兩種功能，保留套管和防止桿旋轉。

23、The extra long bushing offers excellent load bearing characteristics.
額外的長期套管提供出色的承載特性。

24、Bored secant pile is mostly constructed by bushing pile rig in our country.
咬合樁在國內一般使用套管鉆機施工。

25、Place Taper-lock Bushing and Timing Belt Pulley on the transmission shaft.
將錐面緊固套與同步帶輪裝在傳動輪上。

26、Bushing is one of the most important insulation parts in transformer.
套管是變壓器中一種重要的部件。

27、Self-lubricating rod bushing with a low coefficient of friction for smooth actuation.
自潤滑連桿襯套的低摩擦系數平穩驅動。

28、Master cylinder bushing at the clutch pedal.
離合器踏板處的總泵襯套。

29、In this experiment, the flame stability under large bushing is better than under small bushing.
在實驗中，大套管實驗工況的火焰穩定性比小套管要好。

30、Tighten leaf spring press until bushing is extracted from leaf spring.
上緊葉片彈簧加壓機直到襯套被拔出葉片彈簧。

bushing翻譯