1、The isothermal quenching process of the ductile iron camshaft was analyzed.
對球鐵凸輪軸的等溫淬火工藝進行了分析。

2、One centrally located camshaft per cylinder bank is driven by a fiberglass-reinforced toothed belt.
一個位于中央的每缸銀行是由凸輪軸驅動的玻璃纖維增強型齒形帶。

3、When you increase the RPM, however, this configuration for the camshaft does not work well.
當您增加轉速時，但這種配置的凸輪軸不工作。

4、The camshaft has a cam, on which there is a lob, or bump.
凸輪軸上有一個凸輪，凸輪上有一個凸角。

5、The key technology of hollow assembled camshaft is joint between the shaft and the cam lobes.
中空裝配式凸輪軸的技術關鍵為凸輪和軸體之間的連接。

6、The eccentric may be part of the camshaft itself or may bolt to it.
偏心輪可能與凸輪軸是一體的，也可能是通過螺釘連接的。

7、Rocker arm, Rocker arm shaft, Rocker assembly, Valve guide tube, Camshaft bearing Cap.
氣門搖臂，搖臂軸，搖臂總成，氣門導管，凸輪軸蓋。

8、It's connecting methods are the key technology in assembling camshaft production.
而其連接方法是裝配式凸輪軸制造的關鍵技術。

9、Camshaft is one of the important parts on the automobile engine.
凸輪軸是汽車發動機的重要零件。

10、Calculation of Heat Balance during Mold Filling for Hollow Camshaft in EPC
消失模鑄造空心凸輪軸充型過程中熱平衡計算

11、Applied to ductile iron crankshaft, camshaft and other parts of the grinding and other grinding.
適用于球墨鑄鐵曲軸，凸輪軸等工件的磨削及其它磨削。

12、The camshaft has a cam, on which there is a lob, or bump
凸輪軸上有一個凸輪，凸輪上有一個凸角。

13、The manganate phosphating technology of camshaft is introduced.
介紹凸輪軸的磷化工藝。

14、In its initial stage the change-of the camshaft is performed.
在他的初始階段凸輪軸的轉換被執行。

15、Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸輪軸固定螺栓，并拆去作為一個總成的鏈輪和鏈條。

16、The camshaft also fits inside the block, except on overhead-cam engines.
除了頂置凸輪（OHC）發動機以外，凸輪軸都安裝在氣缸體里面。

17、Install cover for camshaft housing.
安裝凸輪軸室蓋。

18、Analysis on Mold Filling of Hollow Camshaft in EPC
氣化模鑄造空心凸輪軸的充型過程分析

19、Since 1958, an engine with a single overhead camshaft has been used.
從1958年起，便已使用帶有單頂置凸輪機的發動機。

20、Camshaft from the crankshaft through the timing belt or gear or chain drive.
凸輪軸由曲軸通過齒形帶或齒輪或鏈條驅動。

21、Therefore, the camshaft must revolve at exactly half the speed of the crankshaft.
因此，凸輪軸必須以曲軸正好一半的速度旋轉。

camshaft翻譯