1、The major shapes of the impeller are coupled bending and torsion.
整體式葉輪主要振動形式是葉輪的彎扭振動。

2、It is suggested to use the refitted speedometer with mechanical impeller as the sensor.
提出用改裝后的機械式葉輪風速表作為傳感器。

3、Transformative problem of aerofoil impeller is put forward.
提出了機翼型葉輪的改造問題。

4、The design of impeller meridional shape influences directly efficiency of centrifugal pumps.
葉輪軸面圖設計的好壞直接影響離心泵的效率。

5、Optimal design on aerofoil parameter of impeller is made based on the second YQH-100 oil-gas pump.
基于第二代YQH-100油氣混輸泵葉輪的基本參數，對葉輪的翼型參數進行了優化設計。

6、This invention relates to an impeller for data acquisition in a flow.
本發明涉及一種用于在流動物中采集數據的葉輪。

7、Impeller suitable for the suction of greases with a low penetration index.
泵葉適合于吸入低滲透性油脂.

8、The trim exponents vary with the fluid viscosity and impeller diameter ratio at same time.
切割指數同時隨著切割后的直徑比和液體粘度變化而變化。

9、The results show that the kinetic energy in the impeller region is higher than in the bulk flow.
結果表明：湍動能分布不均勻，在葉輪區較高，而在主體區較小；

10、Water ring vacuum pump with the impeller rotation, the gas entered the left crescent-shaped part.
式真空泵隨著葉輪的旋轉，氣體進入左邊月牙形部分。

11、Pump impeller loose, grinding to pump out the bottom end caps.
水泵葉輪松動，磨到水泵出水底端蓋。

12、Stirring speed range: 40~200 R/Min, Impeller form: Push type of bicuspid spiral.
攪拌調速范圍：40～200轉/分，攪拌槳形式：二葉螺旋推進式。

13、The impeller has an outer diameter of 72mm and an inlet diameter of 24mm.
葉輪的外徑為72毫米，進流處直徑為24毫米。

14、With the floating impeller structure design, bring down the motor start and running load.
浮動葉輪結構設計，降低了電機啟動及運行負載。

15、Impeller configuration is matched to the process conditions.
攪拌槳結構與工藝條件相匹配。

16、Alkaline resin chromite sand is used to produce qualified impeller casting.
選用堿性樹脂鉻礦砂生產出合格的葉輪。

17、Impeller suitable for the suction of greases with a low penetration index
泵葉適合于吸入低滲透性油脂

18、The objective of this paper is to build a software for axial fans' impeller designing.
主要工作是開發一種能用于工程實際的軸流風機葉輪設計軟件。

19、CAD method for improving design quality and efficiency of centrifugal pump impeller is provided.
本文為提高離心泵葉輪的設計質量及效率提供了一個新的方法。

20、In the lobed impeller the measuring Chambers are the space between the lobes and the meter housing.
葉輪式測量室是葉輪和流量葉殼體間的空間。

21、The bent pipe makes the flow field of impeller inlet strongly disordered.
與無彎管相比，彎管造成葉輪進口的流場紊亂。

22、Adjustable impeller and the clearance between the boards to ensure efficient operation of the pump.
可調節葉輪與護板之間的間隙，保證泵的高效運行。

23、And then removed the pump shaft shell removed send impeller repair shop repair.
然后將軸拆出泵殼，拆下葉輪送修理廠修理。

24、Here is the impeller of sea water pump, I think it isn't fit for use.
這里是海水泵葉輪，我認為它不適合使用。

25、Whirlpool Qibeng the impeller similar large gas turbines impeller.
漩渦氣泵的葉輪類似龐大的氣輪機的葉輪。

impeller翻譯